Truck Stalls-code p0191--fuel rail pressure sensor! ANSWER
#1
Junior Member
Thread Starter
Join Date: Jan 2010
Location: Western New York
Posts: 9
Likes: 0
Received 0 Likes
on
0 Posts
Truck Stalls-code p0191--fuel rail pressure sensor! ANSWER
So, my 2004 F150 kept stalling on me and i couldnt figure out whatr was wrong with it so i started with the following..after replacing my fuel filter, then my fuel pump...estimated costed of a little over $550, i finally took it to a mechanic and the problem was the fuel pump module. so if ever you run into this problem check this first, its located above the spare tire and its a black box with an aluminum plate on the bottom that is bolted onto the steel frame, and since im up north salt and what not works its way in between these to metal and it corroides the aluminum plate and reveals the electronice circuit board which communicates with the fuel pump, onces this gets wet it shorts out and makes your truck stall. so if anyone runs into this problem, check out your fuel pump module. Hopes this saves some of you some money, unlike myself.
#2
So, my 2004 F150 kept stalling on me and i couldnt figure out whatr was wrong with it so i started with the following..after replacing my fuel filter, then my fuel pump...estimated costed of a little over $550, i finally took it to a mechanic and the problem was the fuel pump module. so if ever you run into this problem check this first, its located above the spare tire and its a black box with an aluminum plate on the bottom that is bolted onto the steel frame, and since im up north salt and what not works its way in between these to metal and it corroides the aluminum plate and reveals the electronice circuit board which communicates with the fuel pump, onces this gets wet it shorts out and makes your truck stall. so if anyone runs into this problem, check out your fuel pump module. Hopes this saves some of you some money, unlike myself.
#3
Moderator (Ret.)
Good information yes, and it's been talked about here before. Folks can search out their problem and save money.
Last year a bunch of these failed; it was assumed the salty roads up north contributed to the failure. Ford mounted them up against that rail by the spare tire, and many think water, mud, and salt from the roads gets between the module and rail, making it corrode and rust out (the metal backing. The fix was discussed and found to be a good solution: install a few washers between the module mounting holes and the rail to allow about a quarter inch or so of space. This way the module back will not trap water, mud, or whatever. Another possible fix is to use some silicone around the edge to keep the water, mud, and grim out.
Also, if your dealer is out of the F150 part, the Mercury part is exchangable; some of the parts guys don't know this.
This was all discussed here last year.
Last year a bunch of these failed; it was assumed the salty roads up north contributed to the failure. Ford mounted them up against that rail by the spare tire, and many think water, mud, and salt from the roads gets between the module and rail, making it corrode and rust out (the metal backing. The fix was discussed and found to be a good solution: install a few washers between the module mounting holes and the rail to allow about a quarter inch or so of space. This way the module back will not trap water, mud, or whatever. Another possible fix is to use some silicone around the edge to keep the water, mud, and grim out.
Also, if your dealer is out of the F150 part, the Mercury part is exchangable; some of the parts guys don't know this.
This was all discussed here last year.
Last edited by Mod (Ret.); 06-21-2011 at 01:33 AM.
#4
2008 F150 flex fuel still showing code
So I started by replacing the fuel pump, fuels pump driver module, fuel rail pressure sensor and two vvt solenoids. The code is still there for the fuel rail pressure sensor.
any ideas?
any ideas?
#8
yes. Was obviously kidding him a bit. But he posted same/similar post 2+ months ago, received multiple replies trying to help him.... none of which were acknowledged or followed up on. Seems a bit strange.
#9
Well he was wrong, after further investigation the fuel pump that I had just replaced had a failure. Replaced the failed pump, while reinstalling the fuel tank I found two fuel lines that had apparently be pinched between the fuel tank and the frame rail. I straightened out the lines reinstalled the fuel tank and the truck is now running like new. I will admit that this is the easiest fuel tank I have ever removed and installed.