Tire and wheel fitment guide for 04-08
#341
Senior Member
Tires: Nitto Trail Grappler M/T 305/70-20
Rims: XD Addict Black
Size: 20x9
which one to go with ??
-12mm 4.50"
+18mm 5.71"
How much will each stick out past the fender ??
If I go with a bushwacker pocket style fender flares, what will look good ??
I have a 2wd with 2.5" leveling kit (for now), might do a 6" pro comp lift in the near future.
thanks
Rims: XD Addict Black
Size: 20x9
which one to go with ??
-12mm 4.50"
+18mm 5.71"
How much will each stick out past the fender ??
If I go with a bushwacker pocket style fender flares, what will look good ??
I have a 2wd with 2.5" leveling kit (for now), might do a 6" pro comp lift in the near future.
thanks
#342
Hello, i have a 2006 ford f150 screw lariat with the factory 20 inch wheels
I want to put nitto trail grappers on, size 295/65/20. Also i would get a 2.5 inch leveling kit. Will it work? I know i have to trim up the plastic, but will i have to cut any metal behind the plastic inner wheel well? Will it hit the upper control arm?? Oneperson on here has them on his truck, but then someone else says theirs wouldnt work and that it hit the control arm. Would an allignment help with this? They are only 35's and according to this they should work. My wheel width is 8.5 inch, i dont know about the backspacing. Please help!
I want to put nitto trail grappers on, size 295/65/20. Also i would get a 2.5 inch leveling kit. Will it work? I know i have to trim up the plastic, but will i have to cut any metal behind the plastic inner wheel well? Will it hit the upper control arm?? Oneperson on here has them on his truck, but then someone else says theirs wouldnt work and that it hit the control arm. Would an allignment help with this? They are only 35's and according to this they should work. My wheel width is 8.5 inch, i dont know about the backspacing. Please help!
#344
Senior Member
#345
ok... so i have a 2008 f150 super crew 4x4 and i just bought a hellbent steel leveling kit and i wanted to know if i would have a problem fitting my 305 65 18 moto metal on bf goodrich AT. i got a very good deal on the wheels so i had to grab them. o and the leveling kit is 2.5"..... if you could help me out i would appriciate it. thanks alex
#347
need help
have 2005 4wd f150 have loud grinding sound from both front wheels when driving. it is worst when warm out. if i slow down i can hear the sound slow down and pop then quit fist on the pass side then the driver side.
#348
Senior Member
Join Date: May 2010
Location: San Antonio, TX
Posts: 136
Likes: 0
Received 0 Likes
on
0 Posts
XD Spy's 17x9
Ok gents, I have tried to read through a lot of these posts, yet cannot determine what I can run with my current setup.
06 XLT 2WD
2" Leveling Kit
315/70R17
As far as aftermarket wheels go....what can I get away with? Right now I only rub @ FULL CRANK and its very MINOR....
Thanks,
Mardybum
06 XLT 2WD
2" Leveling Kit
315/70R17
As far as aftermarket wheels go....what can I get away with? Right now I only rub @ FULL CRANK and its very MINOR....
Thanks,
Mardybum
#349
Senior Member
here ya go. should work although yours is 2wd
#350
Senior Member
found some 22"x11 KMC Monster XD, backspacing is 4.27", will it stick out too much ??
and if I throw some 33" on there, will I have rubbing issues ?
2wd with 2.5" level
and if I throw some 33" on there, will I have rubbing issues ?
2wd with 2.5" level
Last edited by Krazy; 12-14-2010 at 03:17 PM.