stalled while towing lots of CODES HELP!!
#1
stalled while towing lots of CODES HELP!!
The truck, 2007 mark lt 5.4l 325 000kms coil and plugs were done at 260 000.
I was towing an enclosed trailer approx 3000 total trailer weight. I was slowly accelerating from a traffic light up to highway speed. The truck sputtered at around 80 km/h than pretty much stalled right out. I checked the codes on the road side.
P0351
P0352
P0353
p0354
p0355
p0356
p0357
p0358
p0750
P0962
I'm hoping the last to codes, which are transmission codes, are just the because the truck lost power while driving.
The dash did indicate something about transmission malfunction.
I cleared the codes on the side of the road. it cranks but will not restart. and the codes don't come back.
I towed it home on a trailer. still no starting. I really don't know where to start looking for a problem on this one.
All help is appreciated.
I was towing an enclosed trailer approx 3000 total trailer weight. I was slowly accelerating from a traffic light up to highway speed. The truck sputtered at around 80 km/h than pretty much stalled right out. I checked the codes on the road side.
P0351
P0352
P0353
p0354
p0355
p0356
p0357
p0358
p0750
P0962
I'm hoping the last to codes, which are transmission codes, are just the because the truck lost power while driving.
The dash did indicate something about transmission malfunction.
I cleared the codes on the side of the road. it cranks but will not restart. and the codes don't come back.
I towed it home on a trailer. still no starting. I really don't know where to start looking for a problem on this one.
All help is appreciated.
#2
So it's saying ALL your coils are bad... got a fuse blown?
Last edited by Martian; 05-17-2016 at 02:29 PM.
#3
Yeah... this is all telling me you have an electrical problem somewhere. Check all fuses and relays everywhere and possibly the wiring in the transmission if you can get to it. Something could be pinched or shorted.
http://www.autoserviceprofessional.c...d-transmission check that out
http://www.autoserviceprofessional.c...d-transmission check that out
Last edited by Martian; 05-17-2016 at 02:46 PM.
#5
fuse 32 was blown.
Now it starts.
the only remaining code is p0358
I replace coil on cylinder 8 ( back drivers side). Once it was removed I could see it was physically cracked.
The same code is still there, so I replaced the plug, it went well but the plug was in good condition, changed it anyways.
code still there.
the power is at there coil connector but the pulsing ground from the pcm is NOT there. I'll be working on it later.
Btw I was towing a new to me rzr 800 in the trailer so out it came and it was our ride home for about 35 miles. Pretty cool given the circumstances.
For some reason I cant post from my phone, otherwise Id respond with pictures.
Still any help is appreciated!!
Now it starts.
the only remaining code is p0358
I replace coil on cylinder 8 ( back drivers side). Once it was removed I could see it was physically cracked.
The same code is still there, so I replaced the plug, it went well but the plug was in good condition, changed it anyways.
code still there.
the power is at there coil connector but the pulsing ground from the pcm is NOT there. I'll be working on it later.
Btw I was towing a new to me rzr 800 in the trailer so out it came and it was our ride home for about 35 miles. Pretty cool given the circumstances.
For some reason I cant post from my phone, otherwise Id respond with pictures.
Still any help is appreciated!!
#7
Trending Topics
#8
#9
fuse 32 was blown. Now it starts. the only remaining code is p0358 I replace coil on cylinder 8 ( back drivers side). Once it was removed I could see it was physically cracked. The same code is still there, so I replaced the plug, it went well but the plug was in good condition, changed it anyways. code still there. the power is at there coil connector but the pulsing ground from the pcm is NOT there. I'll be working on it later. Btw I was towing a new to me rzr 800 in the trailer so out it came and it was our ride home for about 35 miles. Pretty cool given the circumstances. For some reason I cant post from my phone, otherwise Id respond with pictures. Still any help is appreciated!!
#10
Took the ecm out today, opened it up and found a bad transistor, physically burnt, darkened area on the board. Found one at a local wrecker, $100. Not bad bad i thought. Stuck it in but than it would start so I'm positive it needs to be programmed by a dealer. I have an appointment friday morning.