Console Shift Indicator Light
#1
Console Shift Indicator Light
2005 F150 Lariat Screw
Last night the Console shift indicator light was out. All the other dash lights worked normally. I rapped my knuckles on the lower part of the selector (towards the console storage) and it came on.
I believe that the filament is broken and needs to be replace. I looked in the owners manual and it says all instrument lights see dealer.
Does anyone have the factory service steps to replace this? Would love the forum all the more to get this here.
Last night the Console shift indicator light was out. All the other dash lights worked normally. I rapped my knuckles on the lower part of the selector (towards the console storage) and it came on.
I believe that the filament is broken and needs to be replace. I looked in the owners manual and it says all instrument lights see dealer.
Does anyone have the factory service steps to replace this? Would love the forum all the more to get this here.
The following users liked this post:
SilverSport (01-13-2019)
#2
Moderator (Ret.)
Welcome aboard! The new folks get one freebie search done for them.
Check this post; it will help you:
https://www.f150forum.com/f4/having-...roblems-13917/
Check this post; it will help you:
https://www.f150forum.com/f4/having-...roblems-13917/
The following users liked this post:
SilverSport (01-13-2019)
#3
I did attempt a search and I had included the word transmission and nothing relevant came up.
Here is what I found on the suggested post.
open the center console, stick you finger in the hole, pull to the driverside and lift up at the same time, it'll pop open, then you can get to the 197 bulb... it goes in from the back and the bulb points toward the dash.
When I open my console and inspect the interior for a Hole there is none. Maybe someone could post a pic? That would be great.
TIA Douglas
Here is what I found on the suggested post.
open the center console, stick you finger in the hole, pull to the driverside and lift up at the same time, it'll pop open, then you can get to the 197 bulb... it goes in from the back and the bulb points toward the dash.
When I open my console and inspect the interior for a Hole there is none. Maybe someone could post a pic? That would be great.
TIA Douglas
The following users liked this post:
SilverSport (01-13-2019)
#4
Moderator (Ret.)
You're ahead of the game for doing a search!
Here's something our resident F150 console (and many other topics) expert GATORB8 wrote up for removing the shifter; I'd think this same write up could be used in gaining access to the light bulb as well. Take a look:
Transmission Selector Lever - Floor Shift
Removal
1. Remove the floor console left side kick panel.
2. Lift the console storage lid cover and remove the console finish panel.
3. Disconnect the transmission shift cable from the arm of the transmission floor shifter.
4. Disconnect the transmission shift cable from the transmission shift cable bracket on the transmission floor shifter.
5. Remove the transmission floor shifter screws.
6. Disconnect the transmission floor shifter electrical connector and remove the shifter from the vehicle.
7. Using a suitable tool, pry forward on the top of the selector lever button and remove the button.
8. Remove the screw, slide the selector lever **** up and remove the ****.
9. Remove the selector lever **** shroud.
10. Disconnect the transmission control (TC) switch electrical connector and remove it from the selector lever housing.
11. Remove the PRNDL bulb from the selector lever housing.
12. Remove the screws and separate the top and bottom halves of the selector lever assembly.
Installation
1. Position the top and bottom halves of the selector lever assembly together and install the screws.
2. Install the PRNDL bulb in the selector lever housing.
3. Connect the TC switch electrical connector and install the connector on the selector lever housing.
4. Install the selector lever **** shroud.
5. CAUTION: Do not overtighten the screw or damage to the selector lever **** can occur. Position the selector lever **** on the selector lever and install the screw.
6. Position the selector lever button in place and press in on the top of the button to install.
7. Position the transmission floor shifter assembly in the console and install the screws.
o Tighten to 12 Nm (9 ft. lbs.) .
8. Connect the transmission floor shift harness electrical connector.
9. Install the transmission shift cable in the transmission floor shifter cable bracket.
10. Connect the transmission shift cable to the transmission selector arm.
11. Install the console finish panel.
12. Install the left console kick panel.
Here's something our resident F150 console (and many other topics) expert GATORB8 wrote up for removing the shifter; I'd think this same write up could be used in gaining access to the light bulb as well. Take a look:
Transmission Selector Lever - Floor Shift
Removal
1. Remove the floor console left side kick panel.
2. Lift the console storage lid cover and remove the console finish panel.
3. Disconnect the transmission shift cable from the arm of the transmission floor shifter.
4. Disconnect the transmission shift cable from the transmission shift cable bracket on the transmission floor shifter.
5. Remove the transmission floor shifter screws.
6. Disconnect the transmission floor shifter electrical connector and remove the shifter from the vehicle.
7. Using a suitable tool, pry forward on the top of the selector lever button and remove the button.
8. Remove the screw, slide the selector lever **** up and remove the ****.
9. Remove the selector lever **** shroud.
10. Disconnect the transmission control (TC) switch electrical connector and remove it from the selector lever housing.
11. Remove the PRNDL bulb from the selector lever housing.
12. Remove the screws and separate the top and bottom halves of the selector lever assembly.
Installation
1. Position the top and bottom halves of the selector lever assembly together and install the screws.
2. Install the PRNDL bulb in the selector lever housing.
3. Connect the TC switch electrical connector and install the connector on the selector lever housing.
4. Install the selector lever **** shroud.
5. CAUTION: Do not overtighten the screw or damage to the selector lever **** can occur. Position the selector lever **** on the selector lever and install the screw.
6. Position the selector lever button in place and press in on the top of the button to install.
7. Position the transmission floor shifter assembly in the console and install the screws.
o Tighten to 12 Nm (9 ft. lbs.) .
8. Connect the transmission floor shift harness electrical connector.
9. Install the transmission shift cable in the transmission floor shifter cable bracket.
10. Connect the transmission shift cable to the transmission selector arm.
11. Install the console finish panel.
12. Install the left console kick panel.
Last edited by Mod (Ret.); 09-29-2010 at 01:06 PM.
The following users liked this post:
SilverSport (01-13-2019)
The following users liked this post:
SilverSport (01-13-2019)
The following users liked this post:
SilverSport (01-13-2019)
#7
something to tackle when it gets a bit warmer here...thanks!
Bill
Bill
Trending Topics
#8
actually instructions on this Forum made this easy enough to tackle yesterday...works like new!
Bill
Bill