Lets see those Leveled out f150s!!!!
#3511
Member
No clue. I can only tell you that I disconnected my battery and didn't have a problem.
#3515
Member
I checked all my hardware, everything was still torqued fine.
#3516
Senior Member
After first properly installing any kit and torquing everything to where it's supposed to be, you should check everything again at about 300-500 miles and make sure that nothing is getting loose. Even when you install everything "perfectly", things will tend to "settle" just enough that something might lose toque and start to loosen up.
Case in point, I had 1 of the 3 nuts start to loosen on the passenger side of my upper strut mount after putting my kit in. The other two were still torqued properly, and nothing bad was going to happen (at least not then) ... but I obviously had to re-torque that one nut. The rest were still very near proper torque specs, but I re-torqued just to get them good and tight.
On my rear blocks, I checked the nuts on the u-bolts after about 300 miles and none were really loose, but all 8 needed to be re-torqued just a little bit after everything settled in.
It's so easy to check most of that stuff, even w/out a torque wrench. You should be able to tell if something is loose enough that it needs to be re-torqued. If so, just tighten yourself, and get to a shop in the next week or so and have them use a torque wrench to finish the job to proper specs. Most places around here that are willing to install kits will do the re-torque for no charge. They know it needs to be done, even if nothing is loose, it's just good to double-check and make sure.
Case in point, I had 1 of the 3 nuts start to loosen on the passenger side of my upper strut mount after putting my kit in. The other two were still torqued properly, and nothing bad was going to happen (at least not then) ... but I obviously had to re-torque that one nut. The rest were still very near proper torque specs, but I re-torqued just to get them good and tight.
On my rear blocks, I checked the nuts on the u-bolts after about 300 miles and none were really loose, but all 8 needed to be re-torqued just a little bit after everything settled in.
It's so easy to check most of that stuff, even w/out a torque wrench. You should be able to tell if something is loose enough that it needs to be re-torqued. If so, just tighten yourself, and get to a shop in the next week or so and have them use a torque wrench to finish the job to proper specs. Most places around here that are willing to install kits will do the re-torque for no charge. They know it needs to be done, even if nothing is loose, it's just good to double-check and make sure.
#3517
Leave your **** stock!!!!!
Well I bought the Icon 2.5 coilovers and 2.0 rears (ICON STAGE 1) from Stage 3 Motorsports. After install......Have to say, i'm regretting it. Got a rattle in the rear. Gonna have installer check it out and if necessary have him contact Icon to troubleshoot the issues.
This post was edited. Sorry for the earlier rant. Really angry.
This post was edited. Sorry for the earlier rant. Really angry.
Last edited by 1badfish; 05-25-2014 at 06:59 PM.
#3518
Geaux Tigers!
Thought I was putting some of the best components on my new 2013 FX4. Bought the Icon Stage 1kit from Stage 3 Motorsports. $1619.00
Truck *** end bounces like a 1974 Cadillac and rattles like something is loose. Front has a rattle or a popping too. I purposely had the front coilovers set for only 2" of lift vs. the maximum 3". I'll likely switch it back to stock. Lesson learned. Leave well enough alone!!!!!
Truck *** end bounces like a 1974 Cadillac and rattles like something is loose. Front has a rattle or a popping too. I purposely had the front coilovers set for only 2" of lift vs. the maximum 3". I'll likely switch it back to stock. Lesson learned. Leave well enough alone!!!!!
#3519
Brodozin' through life
iTrader: (3)
Thought I was putting some of the best components on my new 2013 FX4. Bought the Icon Stage 1kit from Stage 3 Motorsports. $1619.00
Truck *** end bounces like a 1974 Cadillac and rattles like something is loose. Front has a rattle or a popping too. I purposely had the front coilovers set for only 2" of lift vs. the maximum 3". I'll likely switch it back to stock. Lesson learned. Leave well enough alone!!!!!
Truck *** end bounces like a 1974 Cadillac and rattles like something is loose. Front has a rattle or a popping too. I purposely had the front coilovers set for only 2" of lift vs. the maximum 3". I'll likely switch it back to stock. Lesson learned. Leave well enough alone!!!!!
#3520
Hey guys and gals....Im new to the form and figured i would post a couple pics of my new truck. I love it so far. It's a 2013 Lariat. I picked it up about 2-1/2 weeks ago and made a few changes. Auto spring 2.5 leveling spacers, 3in. rear blocks, tint, took of the running boards, 20x9 BMF's and 295-60 Nitto Trail Grapplers, and a Bakflip cover. I love this thing so far. The more miles it gets on it the better it seems to run. I have no complaints at all.......
[/URL]
[/URL]
[/URL]
[/URL]
Last edited by smknvette; 05-25-2014 at 06:58 PM.
The following 2 users liked this post by smknvette:
f150tamer (05-28-2014),
Jeffrey Nelson (08-11-2014)