Upgrading 2011 sony/nav system - how do i hook this up
#1
Upgrading 2011 sony/nav system - how do i hook this up
I want to upgrade my sony system to run on the factory nav HU...
Polk db571s in the door
JL 8w3v3-4
rockford 400x4 @4ohmfor the door speakers
rockford 400x1 @4ohm for sub
how the heck do i make this all work and what else do i need to hook it all up?
the last time i did any stereo install was in highschool in my CRX lol
Polk db571s in the door
JL 8w3v3-4
rockford 400x4 @4ohmfor the door speakers
rockford 400x1 @4ohm for sub
how the heck do i make this all work and what else do i need to hook it all up?
the last time i did any stereo install was in highschool in my CRX lol
#2
Senior Member
iTrader: (1)
I want to upgrade my sony system to run on the factory nav HU...
Polk db571s in the door
JL 8w3v3-4
rockford 400x4 @4ohmfor the door speakers
rockford 400x1 @4ohm for sub
how the heck do i make this all work and what else do i need to hook it all up?
the last time i did any stereo install was in highschool in my CRX lol
Polk db571s in the door
JL 8w3v3-4
rockford 400x4 @4ohmfor the door speakers
rockford 400x1 @4ohm for sub
how the heck do i make this all work and what else do i need to hook it all up?
the last time i did any stereo install was in highschool in my CRX lol
#3
On down the highway
iTrader: (4)
If your going with polk..just use the sony amp..use the sub wires thru a loc..and replace only the sub..it be a lot cheaper
If you want amps all around u need line convertor like bit ten or the jl cleansweep. .i think rockford makes one..360??
I went with the bit ten..alpine 5 channel amp and jl sub.. no regrets
If you want amps all around u need line convertor like bit ten or the jl cleansweep. .i think rockford makes one..360??
I went with the bit ten..alpine 5 channel amp and jl sub.. no regrets
The following users liked this post:
dasboata (01-07-2020)
#4
If your going with polk..just use the sony amp..use the sub wires thru a loc..and replace only the sub..it be a lot cheaper
If you want amps all around u need line convertor like bit ten or the jl cleansweep. .i think rockford makes one..360??
I went with the bit ten..alpine 5 channel amp and jl sub.. no regrets
If you want amps all around u need line convertor like bit ten or the jl cleansweep. .i think rockford makes one..360??
I went with the bit ten..alpine 5 channel amp and jl sub.. no regrets
I'm going to get someone else to install it and not looking to do it myself (other than the door speakers) i just want to know what other pieces i need to buy to do it before i find an installer
can i use this LOC? http://www.crutchfield.com/p_161LC6I...y.html?tp=2001
Last edited by schissler; 10-15-2014 at 03:30 PM.
#6
I don't need detailed instructions i just want to know what other hardware i need and a general idea of what hooks up to what.
Trending Topics
#8
HU speaker output > audiocontrol LC6i > 4ch amp > speakers
Sony sub output > audiocontrol LC6i > mono amp > sub
#9
Factory nav> factory Sony amp> new processor> new amps. The processor will sum your input signals and give you your front/rear/sub channels to go to your new amps.
The following users liked this post:
BrandonSBates (10-20-2014)
#10
So your going to cut the output side of your Sony amp. One side of these wires(your Sony amp side) you need to extend and run to your processor for your input. I used my front door speakers and rear door speakers for my input. No tweeters, no sub, no center channel. Now with the other side of those wires you cut(speaker side) you can extend to your amps output so you don't have to run wires in the door. Sorry for the quick crappy drawing but hopefully it makes sense or helps.
The following 3 users liked this post by 48ford: