2015 Sony audio build
#1
Senior Member
Thread Starter
2015 Sony audio build
Hey all! Wanted to start a build thread of my stereo project. I have a 2015 lariat with the Sony and sync mft.
Equipment:
Front - Herts HSK-165 6.5" component
Rear - nothing for now
Center - most likely disconnect
Subs - 2 JL 10w3v3
Amps - earthquake PHD2 (sub)
- Earthquake PH2200w4 (doors)
LOC - Audiocontrol LC6i
Wiring - KnuKonceptz for everything
Deadening - KnuKonceptz
So that's what's going in! Please feel free to ask any questions you have or if u have any suggestions send them my way!
Equipment:
Front - Herts HSK-165 6.5" component
Rear - nothing for now
Center - most likely disconnect
Subs - 2 JL 10w3v3
Amps - earthquake PHD2 (sub)
- Earthquake PH2200w4 (doors)
LOC - Audiocontrol LC6i
Wiring - KnuKonceptz for everything
Deadening - KnuKonceptz
So that's what's going in! Please feel free to ask any questions you have or if u have any suggestions send them my way!
#3
Senior Member
Thread Starter
#4
Senior Member
Thread Starter
I ran my Power cable from the battery to the amp mount location - what a Pain In The ***** to get it through the grommet on the passenger side! Also ran new speaker cable while the panels were off.
Today i added my Sound Deadening to the rear, added my mounting boards and mounted the sony amp.
Partial Install pic of - KnuKonceptz Kno Knoise Sound Deadening
My mounting board painted with texture paint and mounted to the truck
Sony Amp mounted to the board
My KnuKonceptz Karma SS speaker wire....Now which color??? First World Problem I Know...my wife just laughed at me when I asked her
Today i added my Sound Deadening to the rear, added my mounting boards and mounted the sony amp.
Partial Install pic of - KnuKonceptz Kno Knoise Sound Deadening
My mounting board painted with texture paint and mounted to the truck
Sony Amp mounted to the board
My KnuKonceptz Karma SS speaker wire....Now which color??? First World Problem I Know...my wife just laughed at me when I asked her
The following users liked this post:
CougarCruiser (02-27-2016)
#6
From what I've read, you will need resistors on the outputs of that Sony amp or you will run the risk of burning your speakers. I did a build in a 2013 F150 MFT with no resisters and didn't have anything bad happen but I've read 14+ it gets sticky. I've got a 15 platinum I'm going to do a build on but I'm kinda waiting and researching to see what people are coming across. I have a bit ten D I use in my 13 that will go in my 15. Please please please keep us posted on your progress and anything you come across.
What's holding me back from starting my build as of now:
Sony outputs/using resistors
Haven't had time to inspect molex plugs but I need to get 12ga through them
Haven't had time to inspect where I might could get 1/0 through the firewall (if I can).
Looking good so far - best of luck.
What's holding me back from starting my build as of now:
Sony outputs/using resistors
Haven't had time to inspect molex plugs but I need to get 12ga through them
Haven't had time to inspect where I might could get 1/0 through the firewall (if I can).
Looking good so far - best of luck.
#7
Senior Member
Thread Starter
From what I've read, you will need resistors on the outputs of that Sony amp or you will run the risk of burning your speakers. I did a build in a 2013 F150 MFT with no resisters and didn't have anything bad happen but I've read 14+ it gets sticky. I've got a 15 platinum I'm going to do a build on but I'm kinda waiting and researching to see what people are coming across. I have a bit ten D I use in my 13 that will go in my 15. Please please please keep us posted on your progress and anything you come across.
What's holding me back from starting my build as of now:
Sony outputs/using resistors
Haven't had time to inspect molex plugs but I need to get 12ga through them
Haven't had time to inspect where I might could get 1/0 through the firewall (if I can).
Looking good so far - best of luck.
What's holding me back from starting my build as of now:
Sony outputs/using resistors
Haven't had time to inspect molex plugs but I need to get 12ga through them
Haven't had time to inspect where I might could get 1/0 through the firewall (if I can).
Looking good so far - best of luck.
What do you mean by resistors? Please explain and post a link if you could
Trending Topics
#8
http://www.focusst.org/forum/focus-s...id-damage.html
I haven't seen any write ups about the f150's just been told from several people they had to do a similar setup but I haven't tested any of this for myself it just seems to be the consensus.
#9
Senior Member
Thread Starter
Thanks for the link
Got my two (2) JL 10W3v3's installed today....Holy **** these things are awesome, clean, tight, and pack a great punch! these are my first JL subs and i'm sold!
Got my two (2) JL 10W3v3's installed today....Holy **** these things are awesome, clean, tight, and pack a great punch! these are my first JL subs and i'm sold!
#10
Senior Member
iTrader: (1)
Here is a link on a ford focus forum about the concept
http://www.focusst.org/forum/focus-s...id-damage.html
I haven't seen any write ups about the f150's just been told from several people they had to do a similar setup but I haven't tested any of this for myself it just seems to be the consensus.
http://www.focusst.org/forum/focus-s...id-damage.html
I haven't seen any write ups about the f150's just been told from several people they had to do a similar setup but I haven't tested any of this for myself it just seems to be the consensus.