10" SM sub box, for 2016 screw
09-16-2016, 08:08 PM
#21
One Clean Machine
Thread Starter
iTrader: (5)
If my box won't fit behind the rear seat, I'm going to remove the underneath storage piece. Then put the sub box under the seat!
09-19-2016, 09:29 PM
#22
One Clean Machine
Thread Starter
iTrader: (5)
Cancelled the RF Amp, and went with the Alpine MRV-M500 mono amp.
http://www.amazon.com/gp/product/B00...?ie=UTF8&psc=1
As the Alpine, has Auto sensing high level inputs. So I can tap only my rear speakers, and this amp will get the music signal, as well as the Auto turn on. No need for the Line Out Converter, or seperate turn on wire.
Which I love the idea of less crap to run!
http://www.amazon.com/gp/product/B00...?ie=UTF8&psc=1
As the Alpine, has Auto sensing high level inputs. So I can tap only my rear speakers, and this amp will get the music signal, as well as the Auto turn on. No need for the Line Out Converter, or seperate turn on wire.
Which I love the idea of less crap to run!
Last edited by Toddman38; 09-19-2016 at 09:33 PM.
09-24-2016, 08:39 PM
#23
One Clean Machine
Thread Starter
iTrader: (5)
Got my Sub, and all my wiring Installed! Just Waiting for my Amp to arrive via USP, this Monday! Then have to swing by my dealer, to have the oem sub connector Activated, as well.
God, I'm not good at Waiting...
God, I'm not good at Waiting...
09-24-2016, 10:33 PM
#26
One Clean Machine
Thread Starter
iTrader: (5)
Ha, awesome brother... Thats the same spot, Im mounting my amp! I placed a 1x10x10, behind the padded carpet, to secure my Alpine to! Is that what you did?
Yours appears to be a 8" sub, as the box sits a bit lower, and you used a 2x4, to sit the box on...
Yours appears to be a 8" sub, as the box sits a bit lower, and you used a 2x4, to sit the box on...
Last edited by Toddman38; 09-24-2016 at 10:40 PM.
09-24-2016, 10:43 PM
#27
Senior Member
Sub box: Pioneer USDW250T
https://www.amazon.com/Pioneer-UDSW2...2P690S82KN7NPX
Subwoofer: Kenwood Excelon KFC-XW1000F 10
09-24-2016, 10:48 PM
#28
Senior Member
Its a 10" sub, I used a 2x4 and used a hole saw to cut a hole in it to go over the seat bolts so the sub would sit on a flat surface. then used a 1/2 inch x 10 x10 mdf covered in speaker carpet and mounted it to the 2x4 for the amp to mount to, similar to what you did.
The following users liked this post:
FFRidgeway (12-20-2016)
09-24-2016, 11:08 PM
#29
One Clean Machine
Thread Starter
iTrader: (5)
Thanks
Its a 10" sub, I used a 2x4 and used a hole saw to cut a hole in it to go over the seat bolts so the sub would sit on a flat surface. then used a 1/2 inch x 10 x10 mdf covered in speaker carpet and mounted it to the 2x4 for the amp to mount to, similar to what you did.
Its a 10" sub, I used a 2x4 and used a hole saw to cut a hole in it to go over the seat bolts so the sub would sit on a flat surface. then used a 1/2 inch x 10 x10 mdf covered in speaker carpet and mounted it to the 2x4 for the amp to mount to, similar to what you did.
How did you get you audio signal and remote turn on to you Alpine? I tapped the oem sub harness purple and green wire, for both!
09-24-2016, 11:32 PM
#30
Senior Member
When I installed the pioneer amp https://www.f150forum.com/f30/my-xlt-install-347367/
I soldered wires to the speaker outs on the harness and ran it back to the alpine amp speaker level inputs, I didn't take a picture of the final wiring I did to the harness or id show you. The 9 conductor wire I used worked perfect 8 wires tied into the amp and the last one I used for the amp remote wire and wired it to the harness I used.
but this is what I used to solder to the harness https://www.amazon.com/Stinger-SGW99...conductor+wire
The following users liked this post:
Toddman38 (09-25-2016)
