Steering Issues
#1
Kyle Cobb
Thread Starter
Steering Issues
While on the way to my family vacation a few weeks ago i noticed something off with my steering on my 2007 Ford F150. When making a turn i noticed resistance in my steering wheel, specially during making a sharp turn such as a U-turn. Pulled over to check my power steering fluid and noticed the levels were normal. There is no noise coming from my power steering pump either.
I was told by a friend that it my be my rack & pinion unit, seeings how the steering has tough spots in it and the problem is also intermittent. However i would like to have some other opinions...
Also, i am having a hard time finding MOTORCRAFT Rack and pinion, i was told i should use rotorcraft due to the fact i have oversize rims and tires on my truck. Is this true or should i also be looking for different brands also.
Thanks for any advise
I was told by a friend that it my be my rack & pinion unit, seeings how the steering has tough spots in it and the problem is also intermittent. However i would like to have some other opinions...
Also, i am having a hard time finding MOTORCRAFT Rack and pinion, i was told i should use rotorcraft due to the fact i have oversize rims and tires on my truck. Is this true or should i also be looking for different brands also.
Thanks for any advise
#2
Senior Member
Steering Issues
Before replacing the steering rack, try lubing the steering shaft. The u-joints can dry out and create tough spots like you described. You can squirt some wd40 on the u-joint as a test. If the issue goes away, then replace the u-joints or entire shaft. Technically you can just keep spraying wd40 when needed, but I'm not a fan of that stuff as a "fix" and would rather do it right.
The following users liked this post:
KornCobb09 (07-31-2015)
#3
Senior Member
Since you mention the U-turn, have you noticed any issues with under or over steer? Particularly under steer. Did it feel like your steering was locked up when the steering wheel was fully turned? If so, there's a good chance you have an alignment issue. What issue? Parts or adjustment? You need to take it in. A pot hole or curb could be the culprit and for a sudden change I'd suspect this before a R&P problem. Those problems are usually a long process and not sudden. But, that doesn't mean it never happens.
#4
Kyle Cobb
Thread Starter
Since you mention the U-turn, have you noticed any issues with under or over steer? Particularly under steer. Did it feel like your steering was locked up when the steering wheel was fully turned? If so, there's a good chance you have an alignment issue. What issue? Parts or adjustment? You need to take it in. A pot hole or curb could be the culprit and for a sudden change I'd suspect this before a R&P problem. Those problems are usually a long process and not sudden. But, that doesn't mean it never happens.
The most noticeable symptom is when i do make s sharp turn, when i go to turn the wheel back straight the wheel does not correct itself. i have to turn the wheel back to the straight position. No i do not feel it lock up as much as i do just tough to correct itself
#5
Senior Member
Sorry, by lock I meant it doesn't return on its own. What you described is the classic symptom for camber and toe being out of alignment.
Last edited by River1; 07-30-2015 at 05:50 PM.
#7
Kyle Cobb
Thread Starter
Thanks to all with advise on finding a solution to this problem. Went to a couple of different forums and found quite a few people who had this same problem. Turns out all i had to do was grease the u joints in the steering shaft. Now my steering is as good as new.
First i went and sprayed some WD-40 on the upper and lower joints on shaft. and that helped. Knowing that WD-40 would not last went to my local auto parts store and bought a tube of lithium grease. then greased up both U-joints on the steering shaft after doing so i turned the steering shaft back and forth. Now everything seems normal.
AGAIN, thanks and hope this ti bit of information helps.
First i went and sprayed some WD-40 on the upper and lower joints on shaft. and that helped. Knowing that WD-40 would not last went to my local auto parts store and bought a tube of lithium grease. then greased up both U-joints on the steering shaft after doing so i turned the steering shaft back and forth. Now everything seems normal.
AGAIN, thanks and hope this ti bit of information helps.
Trending Topics
#8
Senior Member
Glad you followed up with grease - the WD40 would actually break down what little grease was left in the u-joints. And the feedback to the thread is great for future reference by new members!
#10
Mark
iTrader: (1)
Nice job Lew !! you saved the man $500 for a new rack and pinion...