FORScan - software to enable/disable features in your truck
#5742
Senior Member
iTrader: (1)
I've read through this thread and the Sync thread and didn't see anyone else having this issue.
My cross traffic beeps notifying my when a car is coming as I back up. However, the radar does not light up on the screen alerting me to the direction the cross traffic is approaching. All the sonar/radars stay gray.
It used to do this but I'm not sure when it stopped working.
I updated my SYnc to 2.2 and I have made changes using Forscan.
Anyone else run into this issue after making changes with Forscan?
Edit: I've done the heat/cool buttons added to touchscreen, auto fold mirror, mirror tilt, assisted hill descent button add, double honk off, temp add on dash
My cross traffic beeps notifying my when a car is coming as I back up. However, the radar does not light up on the screen alerting me to the direction the cross traffic is approaching. All the sonar/radars stay gray.
It used to do this but I'm not sure when it stopped working.
I updated my SYnc to 2.2 and I have made changes using Forscan.
Anyone else run into this issue after making changes with Forscan?
Edit: I've done the heat/cool buttons added to touchscreen, auto fold mirror, mirror tilt, assisted hill descent button add, double honk off, temp add on dash
#5743
The FORScan Guy
Thread Starter
I have upgraded to 2.2 also but when it went off the other day I wasn't paying attention to the screen display either. I'll try to test this out tomorrow since the rain is supposedly done for now.
#5744
Junior Member
I've read through this thread and the Sync thread and didn't see anyone else having this issue.
My cross traffic beeps notifying my when a car is coming as I back up. However, the radar does not light up on the screen alerting me to the direction the cross traffic is approaching. All the sonar/radars stay gray.
It used to do this but I'm not sure when it stopped working.
I updated my SYnc to 2.2 and I have made changes using Forscan.
Anyone else run into this issue after making changes with Forscan?
Edit: I've done the heat/cool buttons added to touchscreen, auto fold mirror, mirror tilt, assisted hill descent button add, double honk off, temp add on dash
My cross traffic beeps notifying my when a car is coming as I back up. However, the radar does not light up on the screen alerting me to the direction the cross traffic is approaching. All the sonar/radars stay gray.
It used to do this but I'm not sure when it stopped working.
I updated my SYnc to 2.2 and I have made changes using Forscan.
Anyone else run into this issue after making changes with Forscan?
Edit: I've done the heat/cool buttons added to touchscreen, auto fold mirror, mirror tilt, assisted hill descent button add, double honk off, temp add on dash
#5745
Curly, I have seen that too. I just backed into a parking spot and there were some bushes that caused the cross traffic to alert. The little grey waves did light up this time. I'll keep any eye on it and see if it does indicate like normal. At this point I'm more in the camp of this being a software issue and not a Forscan issue.
Last edited by Texarback; 01-24-2017 at 10:38 AM.
The following users liked this post:
curly11 (01-24-2017)
#5746
Senior Member
iTrader: (1)
I am having the same type of issue. Few changes with FORSCAN (thanks everyone in this thread) Upgraded Sync 2.2 w/hub. I have noticed that the little truck icon and sensors takes much longer to load when I put it in reverse and doesn't seem as responsive in the grey bars. Sometimes I am pulled out, put it in drive and then the "radar truck" shows up in a big blue box in the middle of the screen where it cancels out my camera delay.
#5747
The FORScan Guy
Thread Starter
So I looked at the "radar" lines on the display and they're rear parking aids only and not related to the CTA. The only alert I get for CTA is beeping and notification on the cluster which direction the vehicle approaching the truck is coming from. Wheel a trash can behind the truck and you'll clearly see these working.
I've seen the picture of the truck appearing in a box in the center of the screen when I was using the Lincoln brown theme all the time but since I switched to the Ford Blue GT theme that Dan posted I haven't seen it appear that I can remember.
If anyone wants to try this theme it's the following:
7D0-01-02 0xxx xxxx xxxx
7D0-02-01 xxxx xDxx xxxx
7D0-03-01 xxxx x4xx xxxx
I've seen the picture of the truck appearing in a box in the center of the screen when I was using the Lincoln brown theme all the time but since I switched to the Ford Blue GT theme that Dan posted I haven't seen it appear that I can remember.
If anyone wants to try this theme it's the following:
7D0-01-02 0xxx xxxx xxxx
7D0-02-01 xxxx xDxx xxxx
7D0-03-01 xxxx x4xx xxxx
Last edited by Livnitup; 01-24-2017 at 05:15 PM.
#5749
So I looked at the "radar" lines on the display and they're rear parking aids only and not related to the CTA. The only alert I get for CTA is beeping and notification on the cluster which direction the vehicle approaching the truck is coming from. Wheel a trash can behind the truck and you'll clearly see these working.
I've seen the picture of the truck appearing in a box in the center of the screen when I was using the Lincoln brown theme all the time but since I switched to the Ford Blue GT theme that Dan posted I haven't seen it appear that I can remember.
If anyone wants to try this theme it's the following:
7D0-01-02 0xxx xxxx xxxx
7D0-02-01 0xxx xDxx xxxx
7D0-03-01 0xxx x4xx xxxx
I've seen the picture of the truck appearing in a box in the center of the screen when I was using the Lincoln brown theme all the time but since I switched to the Ford Blue GT theme that Dan posted I haven't seen it appear that I can remember.
If anyone wants to try this theme it's the following:
7D0-01-02 0xxx xxxx xxxx
7D0-02-01 0xxx xDxx xxxx
7D0-03-01 0xxx x4xx xxxx
#5750
Senior Member
So I guess I'm heading to the dealer for this issue because I'm out of ideas... I did the very simple mod to use the mirror flood lights at any time - HOWEVER... they did not work after the mod. Checked connectors for loose/broken wires/connectors and all was well. Put everything back to stock and still no floods. Have constant 12v to pin 1 and 12v to pin 2 with ignition on. THEN I ordered a new module thinking maybe I shorted something in the process - I was very careful so I doubted that happened. Installed the new module - still no floods. Restored ALL Forscan modules to factory As-built - no floods... Any thoughts before I head to the dealer?? Thx for anything you can throw my way...