Beer in the garage and some brainstorming
#1
Beer in the garage and some brainstorming
My buddy and I were sitting I his garage looking at my truck and after a couple beers, he said I should turbo my truck. At first I laughed about it but after a couple more beers I remembered I have a Saab with a turbo on it that is going to scrap soon. How hard would it be to put on it? Would I gain anything? The turbo isn't very big, it is only a little 4 cylinder engine it is on. My truck has the 300 efi in it.
I don't really need any more power, and I don't care much about going fast. So why would I put it on there? For the same reason my buddy is putting a 24 valve into his f250 that already had a great running 7.3 in it... Why not?
I don't really need any more power, and I don't care much about going fast. So why would I put it on there? For the same reason my buddy is putting a 24 valve into his f250 that already had a great running 7.3 in it... Why not?
#2
Senior Member
Why not? Because screwing with a perfectly good motor (assuming it runs well) to try an experiment with a part that is not made for it is just plain stupid. Now, if it is not a good running engine, a turbo add probably will make it worse, especially a Saab turbo. I assume your friend is switching out motors? That's a little different. He will still have a good 7.3 if his experiment doesn't work.
But it is your truck, and I am not your dad. By the way, there is a reason Saab went out of business. And according to my dad who owns a Saab, the car is crap.
But it is your truck, and I am not your dad. By the way, there is a reason Saab went out of business. And according to my dad who owns a Saab, the car is crap.
The following users liked this post:
Ricktwuhk (09-02-2014)
#3
Drive like you stole it
Why not? Because screwing with a perfectly good motor (assuming it runs well) to try an experiment with a part that is not made for it is just plain stupid. Now, if it is not a good running engine, a turbo add probably will make it worse, especially a Saab turbo. I assume your friend is switching out motors? That's a little different. He will still have a good 7.3 if his experiment doesn't work.
But it is your truck, and I am not your dad. By the way, there is a reason Saab went out of business. And according to my dad who owns a Saab, the car is crap.
But it is your truck, and I am not your dad. By the way, there is a reason Saab went out of business. And according to my dad who owns a Saab, the car is crap.
To the OP, I don't think you would be able to make it work, unless you have an unlimited budget which makes anything possible.
The following users liked this post:
Snaggletooth (09-02-2014)
#6
Senior Member
Also, please, don't read into what I write with any kind of ill will. It's your truck, your life, I would expect you to do what you want with it. I was just voicing an opinion. I am not emotionally attached.
#7
No worries I wasn't offended.
Let me rephrase what I said. Do I want to got faster? Yes. Do I want more power? Of course! Do I really NEED more of either? Not really.
I am not really sure how much boost I would get from it, any if it would make a difference. Like said above, I am just being a gear head.
I don't think I would have a problem getting intake and exhaust set up. The oil lines I am not sure about. The waste gate... Not 100 percent on how it works, all I know is it bypasses exhaust around the turbine. There are some hoses going to it, I assume these control it? Since it would be going from a smaller engine to a bigger one, do I even need it?
Let me rephrase what I said. Do I want to got faster? Yes. Do I want more power? Of course! Do I really NEED more of either? Not really.
I am not really sure how much boost I would get from it, any if it would make a difference. Like said above, I am just being a gear head.
I don't think I would have a problem getting intake and exhaust set up. The oil lines I am not sure about. The waste gate... Not 100 percent on how it works, all I know is it bypasses exhaust around the turbine. There are some hoses going to it, I assume these control it? Since it would be going from a smaller engine to a bigger one, do I even need it?
Last edited by Ryan313; 09-02-2014 at 08:53 PM.
Trending Topics
#8
Senior Member
Well, now that you rephrased it, I still don't think it's a good idea. But, if you are going to try, look up a kit that is made for a 300, see what parts you would need and try to fill it in with the Saab parts.
#9
Have a few more beers and toss a 7.3 turbo on it. For the oil line just put a t on the oil pressure sender then drain it back into the oil pan. You'll have to weld a nipple on the oil pan.
#10
Well, I will say that I doubt slob, oops I mean Saab, actually designed and manufactured that turbo. So at least THAT ain't a Saab part (I don't think).
As for putting it on your 300... go for it. Just be ready to buy a new engine if you need that truck. Adding a turbo requires a bottom end that can handle the extra stress, as well as making sure your air/fuel ratio stays within a safe range so you don't burn stuff up. NOT saying it won't work, just saying it *might* kill that 300, and if so then be ready to replace it with either another 300 or whatever other engine you might want.
As for putting it on your 300... go for it. Just be ready to buy a new engine if you need that truck. Adding a turbo requires a bottom end that can handle the extra stress, as well as making sure your air/fuel ratio stays within a safe range so you don't burn stuff up. NOT saying it won't work, just saying it *might* kill that 300, and if so then be ready to replace it with either another 300 or whatever other engine you might want.